Manage stand orders
Select Option
UVB TECHNIK s.r.o.
Ostravska 79 A,
748 01
Hlucin
Czechia
Czechia
Location
Hall map
Fairground map
Contact
Lucie Huláková
Our range of products
Product categories
- 01 Plant and equipment for processing prime and raw materials
- 01.07 Coke oven plants
Coke oven plants
- 10 Electrical engineering and process control technology
- 10.02 Process control technology and automation
Process control technology and automation
- 11 Measurement and test technology
- 11.01 Measurement of physical properties and quantities
Measurement of physical properties and quantities
- 11 Measurement and test technology
- 11.02 Quality control
Quality control
- 11 Measurement and test technology
- 11.04 Analysis and laboratory equipment
Analysis and laboratory equipment
Our products
Product category: Process control technology and automation, Measurement of physical properties and quantities, Quality control, Analysis and laboratory equipment
MTP - Continuous Strip Thickness Gauge
Contact measuring by means of two opposite sensors with diamond contacts. The gauge is lead onto the strip by the operator manually or automatically. Then the measurement proceeds automatically, the measured data are displayed on the evaluation unit. As an option, the gauge can include the PP Visual system which is a PC equipped with software for data processing and reports printing. The gauge can also be used for calibration of non-contact gauges. Its function does not depend on composition of the measured material. The automatic version of the gauge is furnished with a system which enables fast pull-out off the line in cases the strip gets sideways of the track, suddenly breaks or excessively corrugates.
Product category: Process control technology and automation, Measurement of physical properties and quantities, Quality control
Shapemeter roll
The sectional strip tension meter is designed for evaluation of metal strip flatness in cold rolling mills. The principle of the flatness evaluation is based on the measurement of pressure forces of a metal strip in individual zones of the measuring roll. A visual unit displays in real time on a monitor the measured tensions across the strip in the form of columns including required data output for AFC (Automatic Flatness Control) and flat graphical mapping.
Product category: Measurement of physical properties and quantities, Quality control
SZ - Wiping equipment
Surface cleaning is done by wiping by means of two pairs of flexible blades. In addition, in between the pair of blades, strip is cleaned by compressed air. The blades together with the blast bar are attached to the floating frame. The frame offsets side tilt of the strip and its horizontal and vertical motion. The upper and lower cleaning part of the frame are pressed together by a couple of air cylinders. Pressure of the air blast can be continuously controlled.
Product category: Measurement of physical properties and quantities, Process control technology and automation, Quality control, Analysis and laboratory equipment
SURFSCAN - Automatic detection of strip defects
SURFSCAN is a visual inspection system designed for defect detection on non-woven textiles, plastic foils, paper, metal plates, etc. System can detect defects as small as 0,1 mm2 at speeds up to 2000 m/min. Maximum product width is 5 m. System is fully configurable according to customer‘s requirements and can be used in various phases of production process.
Product category: Measurement of physical properties and quantities, Quality control, Analysis and laboratory equipment
Strip profile gauge
The measuring cycle is semi-automatic; operator introduces a sample cutting manually, then enters the sample data and starts the measuring. Within the equipment, the sample is pneumatically gripped by means of spring collets which secure mutual perpendicularity of the measured strip surface and contact sensors. After the sample is gripped, the profile measuring and processing of measuring data follows. The outcome of the measuring process is a chart consisting of graphs and statistical data. The charts can be subsequently printed or electronically archived.
Product category: Coke oven plants
Coke Oven Car Position System
Scanner of car position is a system designed to evaluate mutual position of coke oven machines and chambers of coke oven battery.
Moving the operating machine/car the coding plates passes through the slot of the sensor head, the optical sensors identify the number of coding plate (or the name of the chamber) and simultaneously the distance of the scanning head from the center of the coding plate, located in front of each chamber, is measured.
The device enables more precise car positioning and so prevents the wear of coking chambers which result in increased production efficiency.
Moving the operating machine/car the coding plates passes through the slot of the sensor head, the optical sensors identify the number of coding plate (or the name of the chamber) and simultaneously the distance of the scanning head from the center of the coding plate, located in front of each chamber, is measured.
The device enables more precise car positioning and so prevents the wear of coking chambers which result in increased production efficiency.